+86 136 0258 6490 sales@yl-rack.com

How to Build Cheap Shelves Garage Storage?

Port: 2021.03.18

How to Build Cheap Shelves Garage Storage in 2021 with amazing idea?

In order to store the items in stock or for storing tools, lightweight items Cheap Shelves Garage Storage is used. There is lot of racking system but we are going to put shed over the cheapest one.

As we all know that everyone make use of garage for storing their items. If you create mess on the ground then messy floor will create lot of troubles for you.

It would be a good option if you launch shelving system in your garage, almost 90% of your mess will be gone because of shelving unit.

While working you can easily and quickly pick your item from the shelves. Wall mounted garage shelves are very trendy these days; this is why we decided to share How to Build Cheap Shelves Garage Storage?

Go through it and quickly make your own shelving unit at garage in cheap prices.

How to Build Cheap Shelves Garage Storage? – Hanging a Single Shelf

From today no messier garage now, follow below instructions and make your one.

Step 1:

The very thing that you need to do is to select a place for placing the shelve. Make selection of the place that is enough wide and easily accessible. Choose the place where you are damn sure that the space will not be going to be tightening anymore.

Another thing that you have to do is measurement; pick up the tape, measure on 1 of the divider studs and keep measuring it until you reach the point where you want to place it.

But always make sure about one thing that there is no imbalance in measurement, a bit wrong measurement can put you in a trouble.

It would be good if you make a spot on the wall about calculations or try to write it on the paper otherwise you will forget the measurements.

It would be also a great idea to recheck the measurements, also Check the height of products that you are planning to keep in the rack.

How to Build Cheap Shelves Garage Storage?

Step 2:

Now you have to make use of handsaw to cut 2 boards according to the measurements. Now for side and braces you have to cut the piece that is sixteen inches (forty one cm) long.

Make sure to the number of sides & braces equals to the length of rack divided by 2 12 feet (0.76 m) plus 1. Now you have to cut all the pieces that are necessary for shelf framing.

Note: If you have been working with a power saw then make sure to put on safety glasses, these glasses will secure your eyes from being damage.

How to Build Cheap Shelves Garage Storage?

Step 3:

Now you have to lay the one piece on the floor and clasp sixteen in (forty one cm) board to vertical end. Now you have to drill two pocket holes over it. You can also drive two – three in (5.1–7.6 cm) screws into four pocket holes to protect the side.

After you finish with this, you have to do the same method with  2nd side piece on the other end.

fold

Step 4:

Hold the edge against your wall in such a way that the side pieces are opposite to the divider. Guarantee that there is not unbalancing in the level with wall, this surety will keep the items secure from falling off. Start in the focal point of the casing and drive two to three in (5.1–7.6 cm) screws via back piece to tie down it along divider studs. Use in any event two screws for each divider stud, doing this will not let the shelf move after putting weight on it.

screw

Step 5:

Hold the support or brace board which have the similar length like side boards, opposite to the back piece 2 1⁄2 feet (0.76 m) so it stretches out from divider.

Now you have to drive braces into back piece by utilizing 2 tightens pocket openings that is two to three in (5.1–7.6 cm) long.

Keep appending your support pieces with length of the rack’s edge until you arrive at the second place.

You have to double check the braces for measuring their level, if they sit crooked or tilt then you have to reinstall the braces.

inch

Step 6:

In this Step you have to attach the front board on to the frame. Now against the front edge of braces you have to lay the 2nd large piece of your casing. In order to secure it, drive screws.

done

Step 7:

Now you have to attach the plywood and drive screws at every 6 inches in order to hold it securely. Plywood will make the shelving unit plain and smoother.

How to Build Cheap Shelves Garage Storage?

Last Step for How to Build Cheap Shelves Garage Storage?

This is almost a last step; you have to cut a number of boards equals to how many braces piece you have. Also make sure to trim the ends of boards, after cutting they will be like a trapezoid. Now you have to connect the angled pieces with the braces and sides with 2 in (5.1 cm) screws. Finally it’s all done.

Note: we will recommend you highly that not put any weight on the rack, after installing angle braces you can put weight. If you keep it earlier, studs or screws will fall down.

Conclusion – How to Build Cheap Shelves Garage Storage?

The short conclusion of this Article is that we have shared How to Build Cheap Shelves Garage Storage? The shelving type we have shared in this Article is the cheapest one, if you don’t have enough budget for your garage but want to organize your mess then you must go ahead with this shelving type.

If you are looking for ready-made budget friendly shelving type then then can get in touch YongLi Racking Co. Ltd.

We have decades of experience in making the world’s best shelves with reasonable price. Call us at Mob +86 136 0258 6490 Tel:0755-23219979, you can also email us at Email:sales@yl-rack.com in order to grab the discount prices.